The British BenchWhere the work is done

Derived maker summary

Tier IIIThe British Bench editorial classification — Derived directory summary — all eligible current families share this published physical tier

Pinion

Independent British watch company whose four current regular-production families are assembled, regulated and tested in England by founder Piers Berry, using principally Swiss and German specialist-manufactured components.

Visit official site Back to maker index

Editorial classification

The British Bench editorial classification

The British Bench records documented facts about where design, development, component manufacture, assembly, regulation, testing, quality control and related work take place, then applies its own editorial provenance methodology to those facts. A tier is an editorial classification only. It does not determine whether a watch, company or claim is legally British or British-made; assess compliance with origin, advertising or consumer-protection rules; certify or approve a product or maker; or measure quality, value, legitimacy or company nationality. A higher tier confers no legal status, certification, approval or endorsement. A lower tier does not mean a less-British company, a worse watch, misconduct or an improper or unlawful origin claim.

Headline decision

Tier III

All 4 current production families share this published tier.

Summary scopeDerived current-production families
Evidence statusShown per physical route
Coverage4 of 4 current families classified
SourcePublished CMS record
  • All 4 current production families share this published tier.
  • Tier III is a directory summary derived from the current family classifications below; it does not transfer a physical tier between watches.

Documented factual findings

What happens within the qualifying territory

Published operations are shown here; the route cards identify how The British Bench interprets them for each physical tier.

Case manufacture or finishingDocumented — attributable published primary source

Current steel and bronze case finishing in England

Current steel and bronze cases receive hand finishing in England, but the principal case manufacture remains internationally sourced on the evidence reviewed.

England
Watch assemblyDocumented — attributable published primary source

Current watch assembly by Piers Berry in England

All four current regular-production families are assembled in England by founder Piers Berry, who is also responsible for regulation and testing.

England — Pinion workshop
RegulationDocumented — attributable published primary source

Current movement regulation and multi-position testing in England

Pinion publishes a British movement-regulation and multi-position testing process for every current model; the exact post-casing sequence remains an explicit evidence gap.

England — Pinion workshop
Functional testingDocumented — attributable published primary source

Current watch testing and final inspection in England

Current first-party material documents British testing across the range and final-inspection wording on Pure, while the exact completed-watch release matrix remains unresolved.

England — Pinion workshop

Documented factual findings

What is made or completed elsewhere

Documented imported components and international specialist work remain visible beside domestic operations.

Movement manufactureDocumented — attributable published primary source

Reaxis Swiss Sellita SW200-1 movement supply

Reaxis uses the Swiss Sellita SW200-1, with its British hand-build, regulation and testing route disclosed separately.

Switzerland
Movement manufactureDocumented — attributable published primary source

Neutron Dual Swiss ETA 2893-2 movement supply

Neutron Dual uses the Swiss ETA 2893-2 and is counted separately from Neutron because it follows a distinct movement and complication route.

Switzerland
Movement manufactureDocumented — attributable published primary source

Neutron Swiss Sellita SW200-1 movement supply

Neutron uses the Swiss Sellita SW200-1, with British assembly, regulation, testing and case finishing disclosed separately.

Switzerland
Movement manufactureDocumented — attributable published primary source

Pure Swiss Sellita SW261-1 M movement supply

Pure uses the Swiss Sellita SW261-1 M; the evidenced British route is case finishing, assembly, regulation and testing rather than movement manufacture.

Switzerland

Route-level decisions

Where the physical classification changes

The maker summary never replaces these model- and collection-level decisions.

Current published routes4 decisions
Tier III

Reaxis current route

Collection · Provisional — strong evidence with defined gaps

Current and orderable

The British Bench’s editorial interpretation

  • Current first-party material states that every Pinion model is assembled, regulated and tested in England by founder Piers Berry, creating an identifiable named-maker British final-watch route.
  • Pinion publishes multi-position movement regulation/testing in England and states that this process establishes reliable performance before watches leave Pinion HQ.
  • The evidence strongly supports a Tier III physical route, while exact completed-watch sequencing and release-control details that remain unpublished are retained as provisional evidence gaps rather than inferred.
  • Current steel and bronze cases are hand-finished in England, but this finishing is not treated as principal case manufacture for Tier II.
  • Reaxis is explicitly described as hand-built, regulated and tested in England; current material also describes multi-position regulation by Pinion before release.
  • Reaxis is rated to 100 metres / 10 ATM; current production pressure-test method and traceability are not published.

International work

  • The movement and other principal components are internationally manufactured; Pinion itself identifies Switzerland and Germany as the principal specialist manufacturing network. The British work is shown separately rather than converting international manufacture into a British claim.

Why the next tier is not met

  • Pinion states that key components including cases, dials and movements are manufactured principally by specialist suppliers in Switzerland and Germany. Current evidence does not establish qualifying-territory manufacture from stock, raw material or a genuine unfinished blank of a principal movement, case, dial or complete hand-set family, so Tier II is not met.

Evidence gaps

  • Confirm the current incoming-inspection, dial-fitting, hand-fitting, casing-up and stem/crown fitting or verification sequence at the process depth required by Tier III.
  • Confirm explicitly whether every completed current watch is timed after final casing against Pinion’s documented acceptance tolerance, rather than treating movement regulation or the phrase “final timing test” as sufficient proof of post-casing timing.
  • Confirm the corrective regulation, defined rework or controlled rejection action when a completed watch falls outside tolerance, together with mandatory recheck after intervention.
  • Confirm the completed-watch functional test matrix and the final visual/functional pass-fail release authority before dispatch.
  • Confirm whether the final QC/release result is recorded against each serial number or a controlled production batch.
  • For current watches rated to 100 metres / 10 ATM, document pressure-test scope, method, test pressure, location and traceability.

Documented factual findings attached to this route

Documented — attributable published primary sourceCurrent watch assembly by Piers Berry in England

All four current regular-production families are assembled in England by founder Piers Berry, who is also responsible for regulation and testing.

England — Pinion workshop
Documented — attributable published primary sourceCurrent movement regulation and multi-position testing in England

Pinion publishes a British movement-regulation and multi-position testing process for every current model; the exact post-casing sequence remains an explicit evidence gap.

England — Pinion workshop
Documented — attributable published primary sourceCurrent watch testing and final inspection in England

Current first-party material documents British testing across the range and final-inspection wording on Pure, while the exact completed-watch release matrix remains unresolved.

England — Pinion workshop
Documented — attributable published primary sourceCurrent steel and bronze case finishing in England

Current steel and bronze cases receive hand finishing in England, but the principal case manufacture remains internationally sourced on the evidence reviewed.

England
Documented — attributable published primary sourceReaxis Swiss Sellita SW200-1 movement supply

Reaxis uses the Swiss Sellita SW200-1, with its British hand-build, regulation and testing route disclosed separately.

Switzerland

Identifiable evidence supporting this route

C
Pinion — British Watchmaking production route — checked 17 August 2026Pinion Watch Company
C
Pinion — About Pinion maker route — checked 17 August 2026Pinion Watch Company
C
Pinion — current Watches catalogue — checked 17 August 2026Pinion Watch Company
C
Pinion Pure — current product evidence — checked 17 August 2026Pinion Watch Company
C
Pinion Neutron and Neutron Dual — current product evidence — checked 17 August 2026Pinion Watch Company
C
Pinion Reaxis — current product evidence — checked 17 August 2026Pinion Watch Company
Tier III

Neutron Dual current route

Collection · Provisional — strong evidence with defined gaps

Current and orderable

The British Bench’s editorial interpretation

  • Current first-party material states that every Pinion model is assembled, regulated and tested in England by founder Piers Berry, creating an identifiable named-maker British final-watch route.
  • Pinion publishes multi-position movement regulation/testing in England and states that this process establishes reliable performance before watches leave Pinion HQ.
  • The evidence strongly supports a Tier III physical route, while exact completed-watch sequencing and release-control details that remain unpublished are retained as provisional evidence gaps rather than inferred.
  • Current steel and bronze cases are hand-finished in England, but this finishing is not treated as principal case manufacture for Tier II.
  • Neutron Dual uses the ETA 2893-2 dual-time movement and is therefore kept as a distinct current family unit rather than counted as a cosmetic Neutron variant.
  • The shared current Neutron specifications publish in-house three-position regulation and 100 metres / 10 ATM water resistance; exact pressure-test process and final release traceability are not published.

International work

  • The movement and other principal components are internationally manufactured; Pinion itself identifies Switzerland and Germany as the principal specialist manufacturing network. The British work is shown separately rather than converting international manufacture into a British claim.

Why the next tier is not met

  • Pinion states that key components including cases, dials and movements are manufactured principally by specialist suppliers in Switzerland and Germany. Current evidence does not establish qualifying-territory manufacture from stock, raw material or a genuine unfinished blank of a principal movement, case, dial or complete hand-set family, so Tier II is not met.

Evidence gaps

  • Confirm the current incoming-inspection, dial-fitting, hand-fitting, casing-up and stem/crown fitting or verification sequence at the process depth required by Tier III.
  • Confirm explicitly whether every completed current watch is timed after final casing against Pinion’s documented acceptance tolerance, rather than treating movement regulation or the phrase “final timing test” as sufficient proof of post-casing timing.
  • Confirm the corrective regulation, defined rework or controlled rejection action when a completed watch falls outside tolerance, together with mandatory recheck after intervention.
  • Confirm the completed-watch functional test matrix and the final visual/functional pass-fail release authority before dispatch.
  • Confirm whether the final QC/release result is recorded against each serial number or a controlled production batch.
  • For current watches rated to 100 metres / 10 ATM, document pressure-test scope, method, test pressure, location and traceability.

Documented factual findings attached to this route

Documented — attributable published primary sourceCurrent watch assembly by Piers Berry in England

All four current regular-production families are assembled in England by founder Piers Berry, who is also responsible for regulation and testing.

England — Pinion workshop
Documented — attributable published primary sourceCurrent movement regulation and multi-position testing in England

Pinion publishes a British movement-regulation and multi-position testing process for every current model; the exact post-casing sequence remains an explicit evidence gap.

England — Pinion workshop
Documented — attributable published primary sourceCurrent watch testing and final inspection in England

Current first-party material documents British testing across the range and final-inspection wording on Pure, while the exact completed-watch release matrix remains unresolved.

England — Pinion workshop
Documented — attributable published primary sourceCurrent steel and bronze case finishing in England

Current steel and bronze cases receive hand finishing in England, but the principal case manufacture remains internationally sourced on the evidence reviewed.

England
Documented — attributable published primary sourceNeutron Dual Swiss ETA 2893-2 movement supply

Neutron Dual uses the Swiss ETA 2893-2 and is counted separately from Neutron because it follows a distinct movement and complication route.

Switzerland

Identifiable evidence supporting this route

C
Pinion — British Watchmaking production route — checked 17 August 2026Pinion Watch Company
C
Pinion — About Pinion maker route — checked 17 August 2026Pinion Watch Company
C
Pinion — current Watches catalogue — checked 17 August 2026Pinion Watch Company
C
Pinion Pure — current product evidence — checked 17 August 2026Pinion Watch Company
C
Pinion Neutron and Neutron Dual — current product evidence — checked 17 August 2026Pinion Watch Company
C
Pinion Reaxis — current product evidence — checked 17 August 2026Pinion Watch Company
Tier III

Neutron current route

Collection · Provisional — strong evidence with defined gaps

Current and orderable

The British Bench’s editorial interpretation

  • Current first-party material states that every Pinion model is assembled, regulated and tested in England by founder Piers Berry, creating an identifiable named-maker British final-watch route.
  • Pinion publishes multi-position movement regulation/testing in England and states that this process establishes reliable performance before watches leave Pinion HQ.
  • The evidence strongly supports a Tier III physical route, while exact completed-watch sequencing and release-control details that remain unpublished are retained as provisional evidence gaps rather than inferred.
  • Current steel and bronze cases are hand-finished in England, but this finishing is not treated as principal case manufacture for Tier II.
  • The current Neutron route uses Sellita SW200-1 and publishes in-house three-position regulation alongside hand assembly in England.
  • Neutron is rated to 100 metres / 10 ATM; current production pressure-test method and traceability are not published.

International work

  • The movement and other principal components are internationally manufactured; Pinion itself identifies Switzerland and Germany as the principal specialist manufacturing network. The British work is shown separately rather than converting international manufacture into a British claim.

Why the next tier is not met

  • Pinion states that key components including cases, dials and movements are manufactured principally by specialist suppliers in Switzerland and Germany. Current evidence does not establish qualifying-territory manufacture from stock, raw material or a genuine unfinished blank of a principal movement, case, dial or complete hand-set family, so Tier II is not met.

Evidence gaps

  • Confirm the current incoming-inspection, dial-fitting, hand-fitting, casing-up and stem/crown fitting or verification sequence at the process depth required by Tier III.
  • Confirm explicitly whether every completed current watch is timed after final casing against Pinion’s documented acceptance tolerance, rather than treating movement regulation or the phrase “final timing test” as sufficient proof of post-casing timing.
  • Confirm the corrective regulation, defined rework or controlled rejection action when a completed watch falls outside tolerance, together with mandatory recheck after intervention.
  • Confirm the completed-watch functional test matrix and the final visual/functional pass-fail release authority before dispatch.
  • Confirm whether the final QC/release result is recorded against each serial number or a controlled production batch.
  • For current watches rated to 100 metres / 10 ATM, document pressure-test scope, method, test pressure, location and traceability.

Documented factual findings attached to this route

Documented — attributable published primary sourceCurrent watch assembly by Piers Berry in England

All four current regular-production families are assembled in England by founder Piers Berry, who is also responsible for regulation and testing.

England — Pinion workshop
Documented — attributable published primary sourceCurrent movement regulation and multi-position testing in England

Pinion publishes a British movement-regulation and multi-position testing process for every current model; the exact post-casing sequence remains an explicit evidence gap.

England — Pinion workshop
Documented — attributable published primary sourceCurrent watch testing and final inspection in England

Current first-party material documents British testing across the range and final-inspection wording on Pure, while the exact completed-watch release matrix remains unresolved.

England — Pinion workshop
Documented — attributable published primary sourceCurrent steel and bronze case finishing in England

Current steel and bronze cases receive hand finishing in England, but the principal case manufacture remains internationally sourced on the evidence reviewed.

England
Documented — attributable published primary sourceNeutron Swiss Sellita SW200-1 movement supply

Neutron uses the Swiss Sellita SW200-1, with British assembly, regulation, testing and case finishing disclosed separately.

Switzerland

Identifiable evidence supporting this route

C
Pinion — British Watchmaking production route — checked 17 August 2026Pinion Watch Company
C
Pinion — About Pinion maker route — checked 17 August 2026Pinion Watch Company
C
Pinion — current Watches catalogue — checked 17 August 2026Pinion Watch Company
C
Pinion Pure — current product evidence — checked 17 August 2026Pinion Watch Company
C
Pinion Neutron and Neutron Dual — current product evidence — checked 17 August 2026Pinion Watch Company
C
Pinion Reaxis — current product evidence — checked 17 August 2026Pinion Watch Company
Tier III

Pure current route

Collection · Provisional — strong evidence with defined gaps

Current and orderable

The British Bench’s editorial interpretation

  • Current first-party material states that every Pinion model is assembled, regulated and tested in England by founder Piers Berry, creating an identifiable named-maker British final-watch route.
  • Pinion publishes multi-position movement regulation/testing in England and states that this process establishes reliable performance before watches leave Pinion HQ.
  • The evidence strongly supports a Tier III physical route, while exact completed-watch sequencing and release-control details that remain unpublished are retained as provisional evidence gaps rather than inferred.
  • Current steel and bronze cases are hand-finished in England, but this finishing is not treated as principal case manufacture for Tier II.
  • Pure’s current page says every watch is designed, assembled, regulated and tested in England by Piers Berry and describes hand adjustment, multiple-position testing and final inspection.
  • Pure is rated to 100 metres / 10 ATM; current production pressure-test method and traceability are not published.

International work

  • The movement and other principal components are internationally manufactured; Pinion itself identifies Switzerland and Germany as the principal specialist manufacturing network. The British work is shown separately rather than converting international manufacture into a British claim.

Why the next tier is not met

  • Pinion states that key components including cases, dials and movements are manufactured principally by specialist suppliers in Switzerland and Germany. Current evidence does not establish qualifying-territory manufacture from stock, raw material or a genuine unfinished blank of a principal movement, case, dial or complete hand-set family, so Tier II is not met.

Evidence gaps

  • Confirm the current incoming-inspection, dial-fitting, hand-fitting, casing-up and stem/crown fitting or verification sequence at the process depth required by Tier III.
  • Confirm explicitly whether every completed current watch is timed after final casing against Pinion’s documented acceptance tolerance, rather than treating movement regulation or the phrase “final timing test” as sufficient proof of post-casing timing.
  • Confirm the corrective regulation, defined rework or controlled rejection action when a completed watch falls outside tolerance, together with mandatory recheck after intervention.
  • Confirm the completed-watch functional test matrix and the final visual/functional pass-fail release authority before dispatch.
  • Confirm whether the final QC/release result is recorded against each serial number or a controlled production batch.
  • For current watches rated to 100 metres / 10 ATM, document pressure-test scope, method, test pressure, location and traceability.

Documented factual findings attached to this route

Documented — attributable published primary sourceCurrent watch assembly by Piers Berry in England

All four current regular-production families are assembled in England by founder Piers Berry, who is also responsible for regulation and testing.

England — Pinion workshop
Documented — attributable published primary sourceCurrent movement regulation and multi-position testing in England

Pinion publishes a British movement-regulation and multi-position testing process for every current model; the exact post-casing sequence remains an explicit evidence gap.

England — Pinion workshop
Documented — attributable published primary sourceCurrent watch testing and final inspection in England

Current first-party material documents British testing across the range and final-inspection wording on Pure, while the exact completed-watch release matrix remains unresolved.

England — Pinion workshop
Documented — attributable published primary sourceCurrent steel and bronze case finishing in England

Current steel and bronze cases receive hand finishing in England, but the principal case manufacture remains internationally sourced on the evidence reviewed.

England
Documented — attributable published primary sourcePure Swiss Sellita SW261-1 M movement supply

Pure uses the Swiss Sellita SW261-1 M; the evidenced British route is case finishing, assembly, regulation and testing rather than movement manufacture.

Switzerland

Identifiable evidence supporting this route

C
Pinion — British Watchmaking production route — checked 17 August 2026Pinion Watch Company
C
Pinion — About Pinion maker route — checked 17 August 2026Pinion Watch Company
C
Pinion — current Watches catalogue — checked 17 August 2026Pinion Watch Company
C
Pinion Pure — current product evidence — checked 17 August 2026Pinion Watch Company
C
Pinion Neutron and Neutron Dual — current product evidence — checked 17 August 2026Pinion Watch Company
C
Pinion Reaxis — current product evidence — checked 17 August 2026Pinion Watch Company

Source ledger

What this record rests on

Named public sources and public-safe disclosures of confidential reliance are shown without exposing private evidence. The letter is the methodology evidence band, not a product-quality score.

C
Pinion Neutron and Neutron Dual — current product evidence — checked 17 August 2026

Current family page identifying the Sellita SW200-1 Neutron route and separate ETA 2893-2 Neutron Dual route, hand assembly in England, in-house three-position regulation specification and 100-metre water resistance.

Pinion Watch Company
C
Pinion Pure — current product evidence — checked 17 August 2026

Current Pure family page identifying the Sellita SW261-1 M hand-wound route, British assembly/regulation/testing by Piers Berry, multiple-position adjustment, final inspection wording and 100-metre water resistance.

Pinion Watch Company
C
Pinion Reaxis — current product evidence — checked 17 August 2026

Current Reaxis page identifying the Swiss Sellita SW200-1 route, hand build/regulation/testing in England, multi-position regulation wording and 100-metre water resistance.

Pinion Watch Company
C
Pinion — About Pinion maker route — checked 17 August 2026

Current official maker page stating that founder Piers Berry personally designs, assembles, regulates and tests every new Pinion watch in England, while principal components are manufactured internationally.

Pinion Watch Company
C
Pinion — British Watchmaking production route — checked 17 August 2026

Current first-party production page stating that every model is assembled, regulated and tested in England by founder Piers Berry; key components are principally manufactured in Switzerland and Germany; cases are hand-finished in England; and movements are adjusted and tested in three positions before watches leave Pinion HQ.

Pinion Watch Company
C
Pinion — current Watches catalogue — checked 17 August 2026

Current official catalogue separating four regular-production families — Pure, Neutron Dual, Neutron and Reaxis — from the Archive section for previous or custom-build watches.

Pinion Watch Company
Back to all makers